Looking for a durable coating that is UV, chip, impact, & chemical resistant?
Need a non slip surface that is effective, yet gentle on bare feet?
Would you prefer to use a non toxic, non flammable, zero VOC product?

We have the world's leading non skid safety coating designed for decks and submersible surfaces used at leading water parks, theme parks, parks & recreation, luxury ocean vessels, and resorts around the world. Our Non Skid Rubberized Polyurethane Coating AQ is a non toxic, single component, low odor, zero VOC, non flammable, submersible coating that outperforms all other coatings.

AQ is a high build, high flex, durable coating that withstands harsh weather, UV, salt, chemical, impact, and abrasion. Its unique copolymer formulation delivers a flexible coating that resists cracking, peeling and chipping.

This advanced submersible formulation is available with integrated recycled rubber aggregate that effectively enhances slip resistance, yet is gentle on bare feet. With 18 standard colors to choose from and custom colors available, you are left with only your imagination to create the ultimate design with safety in mind for your aqueous environments. Surface areas that don't require the non skid aggregate will enjoy the performance and environmental benefits which in themselves make it a superior coating.

 

Standard Aggregate- 50 to 60 Square Feet per gallon with two coats
Low Aggregate- 60 to 70 Square Feet per gallon with two coats
No Aggregate- 125 to 150 Square Feet per gallon with two coats

Package: 1 Gallon or 5 Gallon Pails
Weight: 10 lbs per Gallon 
Coverage: Standard Aggregate-50-60 sq.ft. p/gal, Low Aggregate- 60-70 sq.ft. p/gal, High Aggregate- 45-50 sq.ft. p/gal, No Aggregate- 125-150 sq.ft. (All coverage estimates are with two coats)

Colors: Black, Dark Grey, Medium Grey, Light Grey, Safety Yellow, Dark Brown, Sand, Tan, Cream, Dark Blue, Medium Blue, Brick Red, Red, Dark Green, Light Green, Safety Orange, White, Clear
Odor: Virtually Odorlesss
Flash Point: N/A Non Flammable
Boiling Point: >100º C
Specific Gravity: 1.05 gm/ml
VOC: Zero

Standard Color Selection:

GENERAL TIPS

It is essential that you always clean each surface that is to be coated.

Remove all grease, oil, and other contaminants; leave no residue, clean thoroughly - if there is any question of contaminants, use a cleaner such as a commercial degreaser or laundry detergent and a scrub brush.

Never assume a surface is clean unless you have cleaned it yourself!

Ensure that the surface (substrate) is sound, dry, and free of all wax, oil, grease and loose materials.

Use ONLY WATER for thinning and clean up.

Keep the Product from freezing.

IMPORTANT!

Testing indicates that adhesion is best when a primer is used. Be sure to apply The Product within the time specifications of the primer manufacturer (CP-10 or MP-10).

PERSONAL PROTECTION

Please review the Material Safety Data Sheet for information on Health Hazards, First Aid, Safe Handling, Emergency Information and other Product Information. It is recommended that you wear: splash-proof goggles; PVC or rubber gloves; rubber boots when working with large quantities; coveralls when working with large quantities, and use a respirator if inhalation risk exists (NIOSH/MSHA approved or organic vapor). The Product can be rolled or sprayed on without any modification!

PROPER PREPARATION IS NUMBER ONE!

HANDY HINTS

Dilute the Product with clean water only if required. A dilution of 10% will reduce the solids within the product by the same amount.

Mask off all areas not to be coated. Make sure to remove the masking tape carefully, immediately after the application of the final coat.

Stir thoroughly before applying and stir periodically to maintain aggregate in suspension.

In order to avoid “cracking” do not allow The Product to pool and do not apply the coats too thick during the application.

When applying The Product, be sure to apply at right angles to the previous coat. Consult the Roller Application Instructions for specifics.

TYPES OF APPLICATIONS

We recommend 2 coats to be considered for standard traffic and 3 coats for heavier traffic or use. The key is to “build up” The Product and not try to achieve thickness in one coat.

ROLLER APPLICATION

Use Foam Texture Rollers only available from Eco-Safety Products. Other rollers may not pick up and spread the product evenly. The roller must be capable of lifting the rubber crumb within the product, to the surface. This will not occur using soft paint rollers. Consult Roller Application Instructions for pretreatment of roller. Pour Product into paint tray or hang roller grid into 5 gallon bucket. Make sure to completely saturate roller with product, leaving no bare spots on roller. Apply the first coat as a thin coat. Resaturate roller after each pass. Make 4 - 5 consecutive passes in the same direction, with each pass right next to the other. When applying, roll in one direction first, then roll in the opposite direction in order to properly blend the product and create a uniform textured surface. Once an area is covered, run the roller very lightly over it to ensure even distribution of color and rubber crumb. When touch dry apply the subsequent coats. Do not apply too thick to avoid “mud cracking”.

SPRAY APPLICATION

NOTE: Reaching a balance between a quality spray finish and one where rubber is poorly distributed is wholly dependent upon technique, spray pressure, spray gun characteristics and the temperature of The Product. Experiment with your technique, spray pressure and spray gun nozzle characteristics until you are satisfied with the finish. It is preferable that The Product be at room temperature (the warmer the better) for easier spraying. If operating in cold climates, without warming the product, achieving satisfactory spray characteristics will take some adjusting to the spray pressure. (Mask off areas as needed)

Use only the spray gun recommended. Superior brand "Spraying-Mantis" hand held Hopper gun, or equivalent. Or for larger projects: Graco brand "Tex-Spray Compact" or equivalent.

Attach spray gun to a compressor airline giving pressure of at least 40 psi. The above spray guns require very low pressure. Spray water out of the gun to prime. Before starting the job, spray a few short bursts away from the surface to test that everything is working properly. Holding gun approximately 12 -24” away from surface, spray an even, light coat over the entire surface. DO NOT APPLY TOO THICK. Keep spray gun at a 90 degree angle to the surface. Spray gun should make a slight "spitting" sound. This is a characteristic of the guns and is necessary for an even texture. The Product will self level. When surface becomes touch dry, spray subsequent coats. While spraying, be careful not to blow rubber crumb away from the area you are working on as this can accumulate in other areas of the job and prevent the polyurethane from bonding with the substrate. If the rubber crumb is bouncing back at you, lower the pressure or hold gun further from the surface. The further away from the surface you hold the gun, the greater the texture, the closer, the finer. Remove any over spray immediately with cloth and water. The Product is very difficult to remove once cured. Clean spray gun with water after each job is completed.

SUBMERSIBLE APPLICATIONS

Make sure you ordered an (AQ) submersible formulation. Follow applicable surface preparation instructions. Allow 5 to 7 days for full cure prior to filling surface area with water.

PRIMERS

Primers are an integral part of our coatings system. The following primers have been tested and are available through Eco-Safety Products. Water Based Epoxy Concrete & Wood Primer - ( Part # ES-EP-CP10): CP10, is a water based, two component epoxy primer. Designed for heavy use and extreme moisture areas. Can be applied to damp concrete surfaces. CP10 takes slightly longer to cure, but is by far our best primer for concrete, wood and painted surfaces. Allow 6 hours for proper cure before applying the topcoats. Apply topcoats within 48 hours of primer application.  Water Based Metal Primer - (Part # ES-EP-MP10): MP10 is a water based, corrosion inhibiting primer. Designed for interior and exterior metal applications. MP10 can also be used on concrete and wood.

APPLICATION TEMPERATURE AND CURING TIME

The Product will be touch dry within 1 hour and can be subjected to light foot traffic within 24 hours. PLEASE NOTE: Full curing time only affects the amount of time required to wait before subjecting the surface to cleaning, heavy loads and chemical exposure. Surface can be subjected to normal loads well before this minimum time requirement. The coating should not be subjected to cleaning, heavy loads, or chemical exposure until fully cured after 7 days, less in hot conditions, more in cold, dry weather. Judgment should be used when determining when the application is fully cured. Dry times in this manual are based on a temperature of 77 degrees Fahrenheit and 50% humidity. Higher temperatures will speed up dry time and colder temperatures will slow it. The product should not be used under 40 degrees Fahrenheit.

Use fans and heat to cure the product more quickly. Do not allow product to freeze.

IMPORTANT: DO NOT USE ANY SOLVENTS, SOLVENT BASED ALCOHOLS, THINNERS OR LACQUERS, TO THIN PRODUCT.

CONCRETE
GENERAL ADVICE FOR CONCRETE APPLICATIONS

Taking into account the following specifically listed concrete notes, unless you are absolutely sure of the (substrate) concrete history, it is important to establish the type of concrete application, the history of the concrete (if various contaminants such as oils, fuels, polishing waxes, chemicals, etc., have been in contact with the concrete), and how the application should be tackled. If there is any doubt at all about any aspect of the concrete history or type, always test (apply) adhesion BEFORE undertaking the overall application. At times, apparently properly prepared substrates do not allow adhesion. If the substrate is properly prepared and no adhesion results, this is usually the result of concrete contamination by chemicals or silicone type materials. These types of contaminants can not be seen even though the prepared concrete looks clean and/or porous. Contaminated substrates of this type will reveal the lifting of The Product in sheet form, revealing adhesion to the primer, but the primer fails to adhere to the substrate. The solution to resolving these types of problems is to establish precisely what the concrete has been exposed to and then to apply the correct cleaning agent to remove the contaminant. For example, long-term fuel contamination will require several degreaser applications to remove all imbedded fuel contaminants. Long term beer contamination in bars will require appropriate cleaning/preparation and a significant drying time period to ensure that beer yeast contamination surfaces from within the concrete and the concrete properly dries. Without this preparation, no adhesion will be possible.

CONCRETE CLEANING

Degreasers: We recommend our bio-based industrial SoyFast Degreaser. They are designed to dissolve the oils, fats, grease, etc. It is very important when using a degreaser that the clean up is absolutely thorough and complete and that no dissolved fat residue is left on the concrete. This is achieved by repeating neutralizing rinses (water) of the concrete.

Important: It is important to do a light acid etch on new concrete and concrete that has been exposed to pool water to remove all lime and mineral deposits. Use two parts water and one part Muriatic acid. Spray on with a weed sprayer and neutralize and rinse thoroughly.

CONCRETE FINISH

The type of concrete finish is critical in the way the application is undertaken. Heavily worked and compressed concrete is NOT porous and adhesion difficulties will be experienced without the correct treatment of the substrate. Likewise, metal trowelled concrete is also difficult to achieve adhesion with, while power trowelling may overwork and compact the concrete and adhesion problems may result. The Product or the primer used must be able to penetrate or attach itself to the substrate in order that satisfactory adhesion occurs. Ideally, concrete should be hand trowelled, porous with a brush/broom finish. New concrete will take up to 28 days to cure properly. Unless the new concrete is dry, adhesion problems will be experienced. Remember, heavily compacted and metal trowelled concrete is essentially waterproof.

CONCRETE

1. Must be fully cured.
2. If concrete surface has a porous texture, no further surface preparation is necessary.
3. If the concrete surface is NOT porous then acid etching, sanding or shot blasting is necessary. Make sure to use a light acid etch and to remove all remaining acid with soap and water and scrub brush. (If all acid is not properly removed, you will not obtain adhesion).
4. Concrete should be completely clean and dry.
5. Patch all imperfections, cracks, etc. with concrete patch filler and flexible joint fillers. These are available at your local hardware store DO NOT USE SILICONE PRODUCTS. (The Product will not adhere to silicone).
6. Prime with CP-10 as per instructions on label. When you feel primer has properly cured, perform test patch to insure adhesion.
7. Apply The Product.

PAINTED SURFACES

1. Aggressively roughen surface by sanding with 36 or 40 grit sand paper. The surface must be rough to proper adhesion.
2. Clean surface of all oils, grease, dirt, silicone and other contaminants. Leave no residue.
3. Inspect for any imperfections or delamination of previously painted surface.
4. Test for adhesion. Prime with CP10.
5. Apply The Product.

ASPHALT
1. Clean surface by pressure-washing.
2. Insure surface is completely dry.
3. Apply asphalt primer. Asphalt primer is available through Sherwin Williams (Part # 8000-01786).
4. Test for adhesion first, before completing job. Apply The Product.

STEEL AND ALUMINUM

All bare metal substrates should be appropriately primed after being treated for rust or removal of old paint.

1. All smooth metal should be cleaned, and aggressively roughed by sanding with 36 or 40 grit sand paper, sand blast or by acid etch. (ACID ETCH IS RECOMMENDED).
2. Clean and dry surface.
3. Prime with MP10.
4. Test for adhesion first, before completing job. Apply The Product.

RUBBER
1. Sand with 36 Or 40 grit sand paper.
2. Clean and dry surface.
3. Prime with rubber primer. Rubber primer is available through Sherwin Williams (Part # DTM Bonding Primer B66 A 50 136-0668).
4. Test for adhesion first, before completing job. Apply The Product.

PLYWOOD, LUMBER AND TREATED LUMBER

1. New lumber needs no sanding. Old lumber requires sanding with 36 or 40 grit sand paper.
2. Remove any peeling, cracking, or chipping paint, varnish or sealer.
3. Ensure surface is clean and completely dry.
4. Prime with CP10.
5. Test for adhesion first, before completing job. Apply The Product.

FIBERGLASS
1. To insure good adhesion, first sand the surface aggressively using a 36 or 40 grit paper to ensure the removal of all gloss from the substrate.
2. Insure that the surface is free of waxes and other protective additives.
3. Clean and completely dry surface.
4. Prime with CP10.
5. Test for adhesion first, before completing job. Apply The Product.

STORAGE AND REPAIR

STORAGE

To store partially used cans, seal can well (airtight) and place in cool, dry place. The contents should be useable for at least 12 months. The evaporation of the water within the product will cause the product to cure. If some water content has evaporated, reconstitution with clean water may restore product viability if the curing process within the can is not too advanced.

REPAIRING

In the event that The Product is damaged, it can easily be repaired, or over-coated, because it bonds to itself. Remove all damaged product. Use a sharp knife such as a utility knife to make a well-defined area such as a square and eliminate uneven edges. Sand area with 36 or 40 grit sandpaper so that the new application can get a good grip. Slightly bevel the edges of the existing product so that the new product can fill in the cutout area and go slightly onto the existing. Clean area with water. Test for adhesion first, before completing job. Then apply The Product to affected area.

RE-COATING

To re-coat an application you must first clean the surface thoroughly to remove all oils, grease, and dirt. Prime with CP10, then re-apply product.

MAINTENANCE

Most general floor cleaners have been tested and will work well. You may consult with Eco-Safety Products for a complete line of “Green Seal” Certified and bio based general cleaners.

DO NOT USE BLEACH, BLEACH PRODUCTS OR CAUSTICS.

For best results, use a stiff bristled deck brush to agitate cleaner on the surface. Rinse surface thoroughly to remove all residue. Surfaces can also be cleaned with use of automatic scrubbers. These are machines which, in one pass, put down the washing solution, scrub the floor with a light pad, and vacuum up the dirty water. It should be pointed out that the pad pressure used in the scrubber must be light and need only be sufficient for the pad to make light contact with the floor. Heavy scrubbing will negatively affect the coated surface.

ADDITIONAL QUESTIONS?

Questions on the application process or on the product, contact: Eco-Safety Products, LLC at (602) 305-9397 Local or (877) 366-7547 TOLL FREE or e-mail questions to: info@eco-safety.com

Theinformation contained herein is given in good faith based upon our experience, knowledge and current information, but without guarantee and the Company accepts no liability whatsoever for its accuracy nor loss or damage arising therefrom. The information is given as a guide only and should not be construed as a full specification. Further, information should be sought from the Company, or its agents regarding specific projects or applications. The Company reserves the right to alter or change this information without prior notice.

NON SKID POLYURETHANE SAFETY COATING PROJECT REFERENCE